Showing results: 316 - 330 of 905 items found.
-
782856-01 -
NI
±60 V, 3 A System PXI Source Measure Unit—The PXIe‑4138 system source measure unit (SMU) delivers high power, precision, and speed. It is ideal for a broad range of applications including manufacturing test; board-level test; lab characterization with devices such as integrated circuits (ICs), power management integrated circuits (PMICs), and radio frequency integrated circuits (RFICs); and discrete devices including LEDs and optical transceivers. The PXIe‑4138 features 4-quadrant operation. The PXIe‑4138 is a hardware-timed instrument with a high-speed sequencing engine for synchronizing acquisitions between multiple SMUs. The module supports direct DMA streaming between the host PC and SMU, so you can stream large waveforms and measurement data at the full update rate and sample rate of the instrument.
-
600 Series Compact ATE Platform -
Circuit Check, Inc.
The Circuit Check 600 Series Compact ATE Platform with built-in professional fixturing solves the uncertainty of repeatable results that are common with bench testing. With the 600 Series Compact ATE, test procedures can become automatic, with test steps and go/no-go limits easily programmable. Hand-probing is eliminated, replaced with accurate, repeatable tooling and reliable spring-loaded test probe fixturing.
-
National Technical Systems
PCB testing, or printed circuit board testing, begins with understanding that the PCB is the foundation for any printed circuit assembly (PCA).The circuit board is a top quality product that should not cause your end product to cost you money due to failures and recalls. NTS is an internationally accredited test laboratory approved for PCB testing including the bare PCB, the raw materials that the PCB is comprised of, as well as the finished PCA. The most commonly used PCB testing performance specifications for qualification, acceptance, and/or conformance are IPC-6012, IPC-6013, IPC-6016, IPC-6018, MIL-PRF-55110, MIL-P-50884, or MIL-PRF-31032.
-
PeakTech Prüf- und Messtechnik GmbH
The PeakTech 2715 is a loop tester which is used to test the safety of electrical systems. These device measures the impedance of the short-circuit loop between the outer conductors of a circuit, whereby the probable short-circuit current is calculated. The protection of the circuit (miniature circuit breaker) must therefore trigger at a lower current than the expected short-circuit current, in order to avoid excessive heating of the lines and thus a fire risk. The PeakTech 2715 is due to its function and its robust design almost indispensable when performing new installations, but also for general checking of electrical systems, this device is the ideal companion.
-
Vogelsang & Benning
Test bench for electric machines and inverters in hybrid applications*Control of mechanical parameters*Verification of electrical properties*Checking the LL characteristics*Short circuit measurement*Recording the performance process*Noise measurement*Temperature measurement
-
Z-Axis Connector Company
Any flat substrate, or bumped substrate, can be compressed against Z-Axis Elastomeric Connectors to make contact. The picture illustrates a Z-Thru Z-Alloy Connector Frame used to connect the DUT (Device Under Test) to a circuit board.
-
TE6-0718 -
Hangzhou Tonny Electric & Tools Co., Ltd.
*For use on 6V, 12V and 24V DC systems*Tests high and low voltages on all vehicle circuits, including computerized engine and body controls*Dual color LED indicates red for power and green for ground
-
HCTS Series -
Shanghai Jiuzhi Electric Co., Ltd.
The HCTS Series Cable Heat Cycle Test System is designed to raise and control the temperature of conductor or other low impedance electrical loop to simulate the current loading conditions found in the electrical circuits up to 10000A.
-
BK2019B -
BaKo Co., Ltd
With the BK2019B, you can test for open/short circuits, operating current and even vibration level. Because it has only one purpose, it is very easy to set up and use and it's so small it can fit into the average briefcase.
-
Testing House, Inc.
Design For Test (DFT) is a technique used to implement certain testability features into a product. Testing House can provide an analysis of the CAD data for testability of your circuit board. Access to a board can be very difficult as boards get smaller and designs get more densely populated. We can work with your design engineer to improve testability and maintain an effective in-circuit test. When access to the board is limited and boundary scan devices are present, we can provide the customer a list of key nodes that will require access in order to provide a very effective test. Our analysis will provide a list of all the accessible test points and an explanation for any nodes declared inaccessible.
-
WABC -
Wuhan Sangao Electrical Test Installations Limit Co.
Acc to IEC and Relevant national standard, In the power transformer production, transfer and user test process, Transformer ratio test is necessary project, This can be used for quality supervision of transformer factory and the use process, prevent the transformer winding inter turn short circuit, open circuit, connection error, pressure regulating switch failure or contact fault.So our company development and production of automatic ratio tester in the original basis according to the user's site using requirements , make the operation more convenient, complete function, stable and reliable data, the testing speed is greatly improved.To meet the needs of all kinds of small medium and large transformer ratio test.
-
PGT120 -
Eltex-Elektrostatik-GmbH
Electronic test apparatus for checking personnel grounding systems such as electrostatic wrist straps and conductive footwear. The unit is equipped with two separate measuring circuits and is therefore capable of checking wrist straps and footwear separately or in parallel. The test result is signaled visually, acoustically (only if error is detected) and via contacts.
-
Z-Axis Europe
FTFs are test fixtures which are dedicated for testing flex-based components and assemblies such as displays, touch panels and more. A weak spot in a typical functional test system is the method to connect DUT flexible cable to a circuit board where the simple method of attaching the flex directly with an ZIF or LIF connector fails.
-
1180 IN -
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Battery operated.● Solid state circuitry.● Battery check feature.● Automatic circuit discharge.● Three insulation test voltages(DC) : 250V, 500V, 1000V● Continuity test : 50 Ω● AC voltage measurement : 500V● Color-coded scale.● Fuse protected.
-
767943 -
Wesbar
Plug these testers into any car connector and you will have an instant test of running light circuits. Features LED display to show completed circuit for the running lights left turn signal and right turn signal. Auxiliary and electric brake circuit are included on the 6-way tester and auxiliary, electric brake and battery charge are included with the 7-way tester. One piece units with internal ground. Proper installation and set-up of a brake control, when a trailer is not readily available, is possible with the 7-way tester. Current Monitor testing device is designed to assist in determining whether a tow vehicle's 7-way blade car end connector has been wired properly. (Current Monitor is an excellent diagnostic tool for installation, setup and troubleshooting of electric trailer brake controls.) The Trailer Tester is designed to help you quickly identify problems in the wiring of the trailer. This is done by testing the Left Turn, Right Turn, Tail/Marker, Brake and Back Up circuits on the trailer. The tester indicates approximate amount of current in each circuit (i.e. trailer battery). Brake Control Bench Tester is a test device designed to determine if a brake control is working properly. Checks brake control output, independent of vehicle wiring. Simulates many fault conditions including open ground, short circuit, open load and more.
